Allaboutexams shares online exam exercise questions all year round! Cisco CCNP Wireless 300-370 exam “Troubleshooting Cisco Wireless Enterprise Networks (WITSHOOT)” https://www.leads4pass.com/300-370.html (104 Q&As). Continue to study and we provide an updated cisco 300-370 exam practice questions and answers. You can practice the test online!
Table of Contents:
- Latest Cisco CCNP Wireless 300-370 pdf
- Test your Cisco CCNP Wireless 300-370 exam level
- Watch the Cisco CCNP Wireless 300-370 video tutorial online
- Related 300-370 Popular Exam resources
- Get Lead4Pass Coupons (12% OFF)
- What are the advantages of Lead4pass?
Latest Cisco CCNP Wireless 300-370 pdf
[PDF] Free Cisco CCNP Wireless 300-370 pdf dumps download from Google Drive: https://drive.google.com/open?id=12Vvbl7aq-Yl_QIwueJekdSrHlX4CcRKm
300-370 WITSHOOT – Cisco: https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/witshoot.html
Cisco CCNP Wireless 300-370 Exam Practice Questions
QUESTION 1
A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change in
the DTPC transmit power threshold must be made to allow APs to globally increase AP transmit power by 3dBm?
A. from 70 dBm to 73 dBm
B. from -70 dBm to -73 dBm
C. from 70 dBm to 67 dBm
D. from -70 dBm to -67 dBm
Correct Answer: D
QUESTION 2
An engineer must open a support case with Cisco TAC. Which two commands verify the model and serial number of a
controller? (Choose two.)
A. show sysinfo
B. show udi
C. show inventory
D. show boot
E. show tech-support
Correct Answer: AB
QUESTION 3
Refer to the exhibit.
An engineer is troubleshooting access point placement issues and suspects that poor placement is causing connectivity
issues. When running the show client detail command, the engineer notices this output. Which option indicates poor
access point placement?
A. excessive number of bytes sent compared to bytes received
B. high signal-to-noise ratio
C. excessive number of data retries
D. low ratio signal strength indicator
E. duplicate received packets
F. poor statistics for the last 90 seconds
Correct Answer: CD
QUESTION 4
Scenario The big Engineering IT team has been in the lab to test some new features that the existing network does not
support. The AP Groups, AP Failover, and Local Web Auth features are having problems. In this test environment, the
controllers support the only Composite Structural Engineering and Aerodynamic Engineering groups. All SSIDs must
omit the department name.
Refer to the exhibit. The diagram is the floor plan for the Big Engineering office and the distribution of the departments.
These tables show how the controllers have been configured.
Note, not all menu items, text boxes, or radio buttons are active.
BE-GA Controller Management Interfaces
Composite and Structural Engineering (CSE) WLANs
AP Groups-CSE-WLANs
AE-User Names and Passwords
You review the configuration of the test network controller. Which four changes must be made to resolve the problems?
(Choose four.)
A. Change the High Availability Primary Controller Management Interfaces IP address for access point 3700-CSE-A.
B. Remove the current WLANs and replace them with WLANs that have the same SSID names as on the AE-2504A
controller.
C. Add the Local Net User names and passwords.
D. Change the Layer2 security to none and Layer3 Security to Web Policy for the CSE-Contractors WLAN.
E. Remove the current WLAN from the CSE-WLAN AP Group and add all three of the WLANs configured in the
CSE-2504A.
F. Add the CSE APs to the CSE-WLANs AP-Group.
G. Change the High Availability Secondary Controller management Interface IP address for access point 3700-CSE-B.
H. Change the High Availability Primary Controller Name for access point 3700-CSE-B.
Correct Answer: BCDF
QUESTION 5
An engineer has discovered that a number of new access points are failing to join the wireless controller module that
has been recently enabled on a switch stack of three Cisco Catalyst 3850 switches running 3.02.03 SE version of Cisco
IOS-XE. All cables have been verified and all access point switch port configurations are identical.
Which options is the likely root cause of the issue?
A. Stacked Cisco Catalyst 3850 switches only support 100 CAPWAP termination licences.
B. Cisco IOS-XE version 3.02.03 SE supports only access points on the master switch.
C. The EULA has not been accepted on the switch wireless controller module.
D. When stacked, the Cisco Catalyst 3850 cannot use the wireless controller module.
Correct Answer: D
QUESTION 6
An engineer is concerned about rogue-on-wire and wants to enable port security. Which guideline must the engineer
follow?
A. Configure Switched Port Analyzer destination ports as secure.
B. Use 802.1x with port security to prevent MAC spoofing.
C. Enable port security on dynamic access ports.
D. Employ static MAC address configuration for APs with port security.
Correct Answer: A
QUESTION 7
Which channel width is the maximum that can be obtained by bonding two 802.11ac subchannels according to US
regulations?
A. 160 MHz
B. 120 MHz
C. 84 MHz
D. 240 MHz
Correct Answer: A
To increase throughput, 802.11ac introduces two new channel widths. All 802.11ac devices are required to support 80
MHz channels, which doubles the size of the spectral channel over 802.11n. It further adds a 160 MHz channel option
for
even higher speeds. Due to the limitations of finding contiguous 160 MHz spectrum, the standard allows for a 160 MHz
channel to be either a single contiguous block or two noncontiguous 80 MHz channels.
References:
QUESTION 8
Which three components are needed to identify the zone of impact for non-802.11 sources of 2.4 GHz and 5.0 GHz
interference? (Choose three.)
A. WLC
B. MSE
C. RF site survey tool
D. Wi-Fi analyzer
E. CleanAir AP
F. spectrum analyzer
Correct Answer: CEF
QUESTION 9
You install a WLAN in a warehouse environment for a customer. three months after the installation, the customer
reports that the devices in the environment show a poor RSSI is some areas. Which option is a possible cause of the
issue?
A. an increase of stock in the warehouse
B. an increase in the number of wireless clients
C. RF interference from external sources, such as microwave ovens
D. another WLAN installed in a neighboring warehouse.
Correct Answer: A
QUESTION 10
Refer to the exhibit. You are debugging a WGB client. Which description of the client is true?
You are debugging a WGB client. Which description of the client is true?
A. disconnected from the wired device
B. triggered to reauthenticate
C. disconnected from the authentication server
D. triggered to roam
Correct Answer: D
QUESTION 11
A mobile workstation in a factory contains an AP that is configured as a workgroup bridge. When the workstation moves,
it loses connectivity and disrupts operation. What can the engineer implement to minimize roaming problems?
A. Use 802.1X authentication.
B. Use Cisco Centralized Key Management for fast roaming.
C. Use AES for encryption.
D. Use the mobile station command.
Correct Answer: B
QUESTION 12
When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?
A. through the primary interface of the group
B. through round robin between interfaces
C. through interface group definition
D. through the interface receiving the first response
Correct Answer: B
QUESTION 13
In a new deployment, your team has connected many access points in a single switch and you noticed that some
access points are not getting power. Which command on a Cisco switch can give you the remaining power (Watts) to
confirm if it is a PoE issue?
A. show power inline
B. show power
C. show post
D. show poe
Correct Answer: A
Related 300-370 Popular Exam resources
| title | youtube | Cisco | lead4pass | Lead4Pass Total Questions | |
|---|---|---|---|---|---|
| Cisco CCNP Wireless | lead4pass 300-370 dumps pdf | lead4pass 300-370 youtube | 300-370 WITSHOOT – Cisco | https://www.leads4pass.com/300-370.html | 104 Q&A |
| lead4pass 300-360 dumps pdf | lead4pass 300-360 youtube | 300-360 WIDESIGN – Cisco | https://www.leads4pass.com/300-360.html | 209 Q&A | |
| lead4pass 300-365 dumps pdf | lead4pass 300-365 youtube | 300-365 WIDEPLOY – Cisco | https://www.leads4pass.com/300-365.html | 144 Q&A | |
| lead4pass 300-375 dumps pdf | 300-375 WISECURE – Cisco | https://www.leads4pass.com/300-375.html | 125 Q&A |
Get Lead4Pass Coupons(12% OFF)
What are the advantages of Lead4pass?
We have a number of Cisco, Cisco, IBM, Cisco and other exam experts. We update exam data throughout the year.
Top exam pass rate! We have a large user base. We are an industry leader! Choose Lead4Pass to pass the exam with ease!
Summarize:
The free Cisco CCNP Wireless 300-370 exam dumps can help you improve your skills and exam experience! To pass the cisco 300-370 exam at once: https://www.leads4pass.com/300-370.html We make Cisco 300-370 videos and 300-370 pdf for you to learn! I hope you can pass the exam easily.